Connecting to the Serial Console¶
Connecting to a Serial Console on pfSense requires a few things:
- A serial port on the client system, either built-in or a USB-to-serial adapter.
- A null modem serial cable, or a device-specific serial cable.
- A terminal program on the client, such as PuTTY.
- The correct serial settings for the client software.
Locating a Serial Port (Server/Firewall)¶
First, ensure the firewall hardware actually has a serial port. To use the serial console, the hardware must have a physical serial port at COM1. Embedded units typically have a DB9 (9-pin) serial port, but some have an RJ45 style console connector with an adapter cable that ends with a DB9 connector.
Locating a Serial Port (Client)¶
The client can use a built-in or USB-to-serial adapter port to connect. The important thing to know is the actual device name used by the port.
On Windows, this is typically COM1 for built-in ports and USB-to-serial ports could be numbered pretty much anything. Check in Device Manager and locate the name, it could be COM3, COM4, etc.
On FreeBSD, the ports are listed in dmesg and are typically /dev/cuau0 for a built-in port at COM1 and /dev/cuaU0 for a USB-to-serial adapter.
On Linux, it could be /dev/ttyS0 or /dev/ttyUSB0
On a MAC, USB-to-serial adapters are generally /dev/cu.usbserial
Null Modem Serial Cables¶
Between the client serial port and firewall serial port, a Null Modem serial cable is required, or a standard serial cable with a Null Modem Adapter. These cables are wired in a special way that rolls the transmit and receive pins allowing the serial ports to properly transmit and receive data from each other.
Some special console cables that ship with embedded systems are already Null Modem cables. Check with the retailer or OEM to find out for sure.
To connect to the serial port, the client and server have to agree on certain parameters, such as the console speed.
The default serial console settings in pfSense 2.2 and later are 115200/8/N/1, meaning:
- Speed: 115200
- Data Bits: 8
- Parity Bits: None
- Stop Bits: 1
Previous releases of pfSense defaulted to a console speed of 9600 but otherwise had the same settings. Devices shipped from retailers with pfSense pre-installed, such as from the pfSense Store or Netgate, typically have the console speed set to match the BIOS. For example, on an ALIX unit, the console speed would be 38400.
There are many serial terminal programs out there for various operating systems. Many of them work well. Some examples are provided here for common usage.
Do NOT use Hyperterminal! It is prone to lose characters/output and generally display things incorrectly.
PuTTY is a Free and easy-to-use SSH and Serial client. To connect to a serial port, start PuTTY and then set the following parameters:
- Connection Type: Serial
- Serial line: Whichever port was determined previously, likely COM1 or COM3 on Windows, or /dev/ttyUSB0 on Linux
- Speed: 115200
The session may be saved for later use. Click Open to start the serial console session.
Using GNU screen on UNIX-based operating systems (Including OSX, where it is available by default) to connect to a serial port is extremely simple. Invoke the program like so:
# screen <port> <speed>
# screen /dev/ttyUSB0 115200
The standard screen controls apply. Press
\ to quit, or
Ctrl-\ in some cases.
tip command on FreeBSD consults
/etc/remotes and connects to
serial ports based on the settings there. To setup a connection to a
USB-to-serial adapter at 115200, add a line such as the following to
To access the port, invoke tip:
# tip ucom1fast
To quit, press Enter, then type ~.. (If connected through a terminal ssh client, ~~. may need to be used instead so that the ssh client itself doesn’t interpret the keys.
Other software has been reported to work, such as minicom, SecureCRT, and cu, among others.